Technical
QUICK DRYING ENAMEL
A quick drying enamel based on a special modified alkyd. It gives a tough, flexible and high gloss finish with excellent leveling. The dried film withstands abrasion, scratch and impact resistances. It can be applied by dip application also.
• Protective coating for structural steel, pipes, scaffolding, drums, vehicles, industrial and agricultural machineries. Most suitable for production line jobs for fast production. It is suitable for interior/exterior surfaces as a part of alkyd systems.
| Shades | AS per shade card |
| Finish Dry film | glossy |
| Specific Gravity | 1.10 ± 0.05 |
| Volume Solids (ASTM D2697) | 50 ± 2% |
| Theoretical Spreading rate (TSR) | 12 – 10 m² / liter |
| Dry film thickness (DFT) | 30 – 40 microns / coat |
| Wet film thickness (WFT) | 60 – 80 microns / coat |
| Flash Point | 30°C |
• Quick drying enamel, gives tough, flexible and high gloss finish with excellent leveling.
Dried film has good abrasion, scratch and impact resistances, suitable for dipping applicatio
• Certificates are available upon request
| 1 liters | 3.64 liters | 14.56 liters |
| TOUCH DRY | 5 – 10 minutes |
| DRY TO RECOAT | 4 – 6 hours |
| FULLY CURED | 10 – 12 hours |
Surface should be clean, dry and free from any contamination. Oil and grease should be removed by solvent cleaning as per SSPC SP-1. Abrasive blast cleaning to Sa 2.5
| Working pot Life@30°C | 1 hours (reduced at higher temperatures) |
| Thinner | Vision Epoxy thinner |
| Airless spray | Tip Range: 0.018” – 0.020” Pressure: 2200 psi Thinner addition: 5–10% |
| Conventional spray | Atomizing pressure: 40 psi Thinner addition: 10–15% |
| Brush, Roller | Thinner addition: 5–10% |
- Avoid skin and eye contact by wearing overalls, gloves, goggles, and mask etc.
- Eyes: In the event of accidental splashes, flush eye with water immediately and obtain medical advice.
- Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
- Avoid inhalation of vapours and paint mist by wearing suitable mask. In the event of ingestion seek medical attention immediately.
- This product is flammable, keep away from sources of ignition. Take precautionary measures against static discharge. In the case of fire – blanket flames with foam, carbon dioxide or dry chemicals.
- Painting must be carried out in well-ventilated area. Local safety regulations need to be followed.
| Vision QD Primer | 60 microns |
| Vision Undercoat | 60 microns |
| Vision top coat | 50 microns |
• Please consult Vision Technical team for other system recommendation.
- Store the paint in proper storage conditions as per the local regulations. Keep the paint container in sealed condition under shed, away from direct sunlight and extreme temperatures.
- Do not keep paint material near to any ignition sources.
- Do not put back the half or unused material back in original container, containing the supplied paint, to avoid contamination.
- Handle with care.
- Stir well before use.
- Shelf life at 30°C is 18 months in original sealed container, with proper storage conditions.
Note
Theoretical Coverage is based on a mathematical formula and does not consider Loss Factor.
[ Volume Solid % x 10/ Dry Flim Thickness (u) ] = m2 /lit? cot
This theoretical coverage rate has been calculated from the volume solids of the material and is related to the amount of coating applied onto a perfectly smooth surface without wastage. For a practical coverage rate, due allowance should be made for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application etc. when estimating quantities required for a particular job. The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the product itself.
Technical Data
Volume Solid: White 43 % (nominal), other colour swill vary
Film Thickness: Wet: 60–70 pm
Dry: 25-30µm
. Drying Time : TouchDry: Single coat at standerf ilm thickness Dependent on temperature and humidity
. Recoating Time : 2–3 hours (Dependent on temperature and humidity).
. No . of Coats : 2–3 coats
. Theoretical Coverage : 9–11 m2 per litter per coat (Actual coverage is dependent on substrate condition, application method, applicationcondition and finishing appearance .
Shelf Life : Upto 24 months in tight sealed container .Shades available as per demand
Note
This theoretical coverage rate has been calulated from the volumes solids of the material and is related to the amount of coating applied onto aperfectly smooth surface without wastage. for a practical coverage rate, due allowance should be made for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application etc. when estimating quantities required for a particular job. the above information is given to the best of our knowledge
WEATHER RESISTANT.
Weather resistant is an excellent quality exterior emulsion which gives a highly durable finished. The product has excellent weather and scrub resistance.
RECOMMENDED USE.
Recommended for exterior / interior use on plaster, concrete, gypsum, brickwork and asbestos surface where long lasting and washable finished is required.
| Paint type | Product type | Finishing | Recommended Substrate | Pack Size |
|---|---|---|---|---|
| Water based | Exterior | Low sheen | Plaster, brick & masonry | 1 liter, 4 liter & 16 liter |
Composition
- Pigment.
- Binder.
- Thinner
Application method
- Spray – Use airless spray
- Brush – Recommended
- Roller – Recommended
Technical Data
- Volume Solid: White 43% (nominal), other colours will vary
- Film Thickness:
Wet: 60 – 70 µm
Dry: 25 – 30 µm - Drying Time: Touch Dry: Single coat at standard film thickness (Dependent on temperature and humidity)
- Recoating Time: 2 – 3 hours (Dependent on temperature and humidity)
- No. of Coats: 2 – 3 coats
- Theoretical Coverage: 9 – 11 m² per liter per coat
(Actual coverage depends on substrate condition, application method, condition, and finishing appearance.) - Shelf Life: Up to 24 months in tight sealed container
- Shades: Available as per demand
Note
Theoretical Coverage is based on a mathematical formula and does not consider Loss Factor.
This theoretical coverage rate has been calculated from the volume solids of the material and is related to the amount of coating applied onto a perfectly smooth surface without wastage. For a practical coverage rate, due allowance should be made for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application etc. when estimating quantities required for a particular job. The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the product itself.
MATT EMULSION.
Matt Emulsion is an Acrylic copolymer based, washable interior/exterior emulsion paint with a smooth flat decorative finish. It offers excellent adhesion and recoatatability. Matt Emulsion is with better hiding power, and exceptional light and weather resistances. Basically, it is for masonry application purpose, with good alkali resistance. It contains anti bacterial and anti fungal additives.
RECOMMENDED USE.
Matt Emulsion is recommended for the masonry applications on concrete, plaster, stucco filler, gypsum board, asbestos, blocks etc. It is used also for sealing the surfaces of stucco filler and gypsum board. It is recommended for the interior/exterior applications of flats, buildings, offices, boundary wall etc. It can also be applied over wooded surfaces also.
| Paint type | Product type | Finishing | Recommended Substrate | Pack Size |
|---|---|---|---|---|
| Water based | INTERIOR/EXTERIOR | Smooth / Matt | Plaster, brick & masonry | 1 liter, 4 liter & 16 liter |
Composition
- Pigment.
- Binder.
- Thinner
Application method
- Spray – Use airless spray
- Brush – Recommended
- Roller – Recommended
Technical Data
- Volume Solid: White 44 ± 2% (nominal), other colours will vary
- Film Thickness: Wet: 80 – 90 µm
Dry: 35 – 40 µm - Drying Time: Touch Dry: Single coat at standard film thickness (Dependent on temperature and humidity)
- Recoating Time: 2 – 3 hours (Dependent on temperature and humidity)
- No. of Coats: 2 – 3 coats
- Theoretical Coverage: 10 – 13 m² per liter per coat
(Actual coverage is dependent on substrate condition, application method, application condition, and finishing appearance) - Shelf Life: Up to 24 months in tight sealed container
- Shades: Available as per demand
Note
Theoretical Coverage is based on a mathematical formula and does not consider Loss Factor.
[ Volume Solid % × 10 / Dry Film Thickness (µ) ] = m² /lit/coat
This theoretical coverage rate has been calculated from the volume solids of the material and is related to the amount of coating applied onto a perfectly smooth surface without wastage. For a practical coverage rate, due allowance should be made for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application etc. when estimating quantities required for a particular job. The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the product itself.
Technical Data
- Drying Time: Touch Dry: 30 minutes (Dependent on temperature and humidity).
- Hard Dry: 1 hour (Dependent on temperature and humidity).
- Recoating Time: 2 – 3 hours (Dependent on temperature and humidity).
- Dry Film Thickness: 30 – 40 μm per coat (based on substrate condition).
- No. of Coats: 2 – 3 coats.
- Theoretical Coverage: 9 – 11 m² per liter per coat (Actual coverage is dependent on substrate condition, application method, application condition and finishing appearance).
- Volume Solid: ~40%
- Shelf Life: Up to 18 months in tight sealed container.
- Shades: Available as per demand.
Surface Preparation
Application Method
| Method | Thinner | Details |
|---|---|---|
| Airless Spray | Vision thinner | Tip: 0.018” – 0.020” Pressure: 2200 psi Thinner: 5–10% |
| Conventional Spray | Vision thinner | Pressure: 40 psi Thinner: 10–15% |
| Thinner | Volume: 20–30% | |
Recommended System
Mist Coat: 1 coat
Hammer Finish: 1 coat
• Consult Vision Technical team for other system recommendations.
Safety Precautions
• If in eyes: Rinse immediately and get medical help.
• If on skin: Wash with soap or cleaner.
• Avoid inhaling vapors or mist.
• Product is flammable. Avoid sparks/static.
• Ensure good ventilation during application.
• Follow local safety regulations.
Storage & Shelf Life
• Keep sealed when not in use.
• Do not return unused paint to original can.
• Stir well before use.
• Shelf life: 18 months at 30°C in sealed condition.
Volume Solid: White 43 % (nominal), other colour swill vary
Film Thickness: Wet: 60–70 pm
Dry: 25-30µm
. Drying Time : TouchDry: Single coat at standerf ilm thickness Dependent on temperature and humidity
. Recoating Time : 2–3 hours (Dependent on temperature and humidity).
. No . of Coats : 2–3 coats
. Theoretical Coverage : 9–11 m2 per litter per coat (Actual coverage is dependent on substrate condition, application method, applicationcondition and finishing appearance .
Shelf Life : Upto 24 months in tight sealed container .Shades available as per demand
Note
This theoretical coverage rate has been calulated from the volumes solids of the material and is related to the amount of coating applied onto aperfectly smooth surface without wastage. for a practical coverage rate, due allowance should be made for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application etc. when estimating quantities required for a particular job. the above information is given to the best of our knowledge
Surface Preparation
Surface should be clean, dry and free from any contamination. Oil and grease should be removed by solvent cleaning as per SSPC SP-1. Abrasive blast cleaning to Sa 2.5.Application Method
| Mixing Ratio (By Volume) | 3 Base : 1 Hardener |
|---|---|
| Working Pot Life @30°C | 4 hours (reduced at higher temperatures) |
| Thinner | Vision Epoxy thinner |
| Method | Details |
|---|---|
| Airless Spray | Tip Range: 0.018” – 0.020”, Pressure: 2200 psi, Thinner addition: 5–10% |
| Conventional Spray | Atomizing pressure: 40 psi, Thinner addition: 10–15% |
| Brush, Roller | Thinner addition: 5–10% |
Recommended System
| Coating | DFT |
|---|---|
| Vision Epoxy Primer | 60 microns |
| Vision Undercoat HB | 125 microns |
| Vision Top Coat | 50 microns |
Safety Precautions
- Avoid skin and eye contact by wearing overalls, gloves, goggles, and mask etc.
- Eyes: In the event of accidental splashes, flush eye with water immediately and obtain medical advice.
- Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
- Avoid inhalation of vapours and paint mist by wearing suitable mask. In the event of ingestion seek medical attention immediately.
- This product is flammable, keep away from sources of ignition. Take precautionary measures against static discharge. In the case of fire – blanket flames with foam, carbon dioxide or dry chemicals.
- Painting must be carried out in well-ventilated area. Local safety regulations need to be followed.
Storage & Shelf Life
- Store the paint in proper storage conditions as per the local regulations. Keep the paint container in sealed condition under shed, away from direct sunlight and extreme temperatures.
- Do not keep paint material near to any ignition sources.
- Do not put back the half or unused material back in original container, containing the supplied paint, to avoid contamination.
- Handle with care.
- Stir well before use.
- Shelf life at 30°C is 18 months in original sealed container, with proper storage conditions.