VISION EPOXY PRIMER
DESCRIPTION
A two pack polyamide cured epoxy resin based primer for protective coating system.
RECOMMENDED USES
- Steel structures, process equipment and pipe work.
- Galvanized steel, Aluminum, Minimum surface prepared substrates.
ADVANTAGES
- Good anti-corrosive properties (atmospheric and immersed exposure conditions).
- Good abrasion resistance.
- Resistant to water and various mild chemicals.
CERTIFICATIONS
• Certificates are available upon request
TYPICAL PROPERTIES
| Color Dry film | Grey, Red |
|---|---|
| Finish Dry film | Smooth & Matt |
| Specific Gravity | 1.40 ± 0.05 |
| Volume Solids (ASTM D2697) | 52 ± 2% |
| Theoretical Spreading rate (TSR) | 6.5 – 10.4 m²/liter |
| Dry film thickness (DFT) | 50 – 80 microns / coat |
| Wet film thickness (WFT) | 100 – 160 microns / coat |
| Flash Point | 25°C |
PACKAGING SIZE
| Pack Size | Base | Hardener |
|---|---|---|
| 4 liters | 3 liters | 1 liter |
| 16 liters | 12 liters | 4 liters |
DRYING TIME
| Temp. | Surface dry (minutes) | Hard dry (Days) | Overcoating interval with recommended top coats |
|---|---|---|---|
| 10°C | 12 | 36 | 36 min – 7 days |
| 20°C | 8 | 30 | 30 min – 7 days |
| 30°C | 6 | 24 | 24 min – 7 days |
| 40°C | 4 | 20 | 20 min – 7 days |
SURFACE PREPARATION
Surface should be clean, dry and free from any contamination. Oil and grease should be removed by solvent cleaning as per SSPC SP-1. Abrasive blast cleaning to Sa 2.5
APPLICATION METHOD
| Mixing Ratio (By Volume) | 3 Base : 1 Hardener |
|---|---|
| Working pot Life @30°C | 4 hours (reduced at higher temperatures) |
| Thinner | Vision Epoxy thinner |
| Airless spray | Tip Range: 0.018” – 0.020” Pressure: 2200 psi Thinner addition: 5–10% |
| Conventional spray | Atomizing pressure: 40 psi Thinner addition: 10–15% |
| Brush, Roller | Thinner addition: 5–10% |
RECOMMENDED SYSTEM
| Vision Epoxy Primer | 60 microns |
|---|---|
| Vision Undercoat HB | 125 microns |
| Vision Top Coat | 50 microns |
• Please consult Vision Technical team for other system recommendation.
SAFETY PRECAUTIONS
- Avoid skin and eye contact by wearing overalls, gloves, goggles, and mask etc.
- Eyes: In the event of accidental splashes, flush eye with water immediately and obtain medical advice.
- Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
- Avoid inhalation of vapours and paint mist by wearing suitable mask. In the event of ingestion seek medical attention immediately.
- This product is flammable, keep away from sources of ignition. Take precautionary measures against static discharge. In the case of fire – blanket flames with foam, carbon dioxide or dry chemicals.
- Painting must be carried out in well-ventilated area. Local safety regulations need to be followed.
STORAGE & SHELF LIFE
- Store the paint in proper storage conditions as per the local regulations. Keep the paint container in sealed condition under shed, away from direct sunlight and extreme temperatures.
- Do not keep paint material near to any ignition sources.
- Do not put back the half or unused material back in original container, containing the supplied paint, to avoid contamination.
- Handle with care.
- Stir well before use.
- Shelf life at 30°C is 18 months in original sealed container, with proper storage conditions.
NOTE: We warranty only the quality of our product and this data sheet is based on results obtained from experience and tests. We reserve the right to change data without prior notice. For safety details kindly refer safety data sheet.